![]() ![]() Key mount is a licensed feature from DeadAir Silencers. We are officially licensed and approved by Dead Air Silencers to incorporate their KeyMo mount design with our. They will support any suppressor that uses a Deadair Silencers “Key mo” quick disconnect adapter. KeyMo Flash Hider and FG42 also available. The RCB-KM models are available in 1/2X28 tpi and 5/8X24 tpi. Check out the specs below and see why the Cobalt RCB is the solution that you have been waiting for. The RCB’s can also be pin/ welded to allow for a 16” OAL on barrels ranging from 13.7” and up. The finest attention to detail was also paid to the material selection, coatings, and tolerances on these units to provide the best possible option for your recoil mitigation needs. The result is an eloquent solution that controls muzzle climb, helps improve split times on follow up shots, and kills excessive muzzle flash. ![]() We accomplished this by designing a port system that optimizes the available gasses without bringing about un-necessary turbulence/ concussive energy back to the shooter. They have had some production and QC issues with BPI of late, and switched to a new manufacturer for their products starting in December, I believe. Our approach was a simple one, to control the expanding gasses exiting the gun so that they can be used to aid in quicker follow up shots. Kind of, Dead Air is an engineering/design shop, they used to partner with BPI (although they werent owned by them) for the manufacture of their cans. I really like this quick mount and dismount method.The RCB family is Cobalt Kinetics solution to solve excessive side blast/ concussion out of large port brakes. I also have a Sandman K and that has the Keymo built into it. The 2 wrenches that come with this setup should allow you to tighten it down enough to keep in from unscrewing as you described. I would strongly suggest that you call or email Dead Air and talk to them about the best way to deal with this. If it is unscrewing on you, you don’t have the Keymo adapter tightened down enough to the Nomad. I have the Muzzle Brakes Rockset to the barrels but I don’t have any thread locker on the junction of the Nomad and the Keymo adapter. RCB-KM Dead Air KeyMo® Details The RCB family is Cobalt Kinetics solution to solve excessive side blast/ concussion out of large port brakes. I have a Dead Air KeyMount Muzzle Brake on a few different firearms and I also have a Nomad30 with the Keymo on it. It has been a while since I have been on here so I only just saw your post. Expand the modularity of your Nomad-30 and Primal. My question is: can I use rocksett or something similar to bond the suppressor to the keymo adapter? I understand it’ll have to be something that can hold up to extreme heat, and also probably won’t be able to take the two apart in the future. If you’re not quite ready to turn up the. When you’re ready for peace and quiet use the Keymount brake to quickly attach your Sandman-L, Sandman-S, Sandman-K to your rifle. Then the keymo will be sitting all by its lonesome on the host. Available for standard 7.62x51mm and 5.56×45 threaded barrels, the Keymount Muzzle Brake is your gateway to silence. However, a small issue I’ve run into that kind of worries me is that after I’ve ratcheted the whole thing onto the host (hand tight) as I start to unscrew it instead of it ratcheting back off the host instead the suppressor will just start to unscrew itself from the keymo. ![]() I followed all instructions to a T when mating the keymo to the suppressor. I’ve also got the keymo adapter mount on it as well. It’s a DeadAir Nomad-30 Ti for a 300 SBR. So I recently got my brand new suppressor out of jail and can’t wait to shoot it.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |